Description
WyreStorm 3-Input In-wall HDBaseT Transmitter
The WyreStorm 3-Input In-wall HDBaseT Transmitter sets a new standard for in-wall HDBaseT transmission. The SW-130-TX-US brings features of the WyreStorm range of professional switchers and packs them into a 2-gang form factor. Automatic or manual switching of the 3 connected sources (2 HDMI and USB-C) is possible with the USB-C supporting alt-mode functionality allowing a portable device such as a tablet or phone to be connected and send its content at up to 4K/30. HDCP 2.2 is also supported for the transmission of encrypted content.
View QuickStart Guide >> View Specifications >>
Features
- HDBaseT switcher/transmitter for video conference or meeting rooms
- Compatible with DVI-I and DP++ v1.3 signals from supported devices
- Additional 2ch analogue audio input for sending separate stereo audio to RX
- Automatic or manual CEC triggering for compatible connected screens or projectors
- Primary power supply via PoH from a supported receiving device (RX-700)
- Additional power input via DC port on rear via 12v 1A PSU (not included). Port shared with RS-232 input
- Control options include automatic switching, manual switching & CEC trigger and RS-232 control
- Compatible with TS-280 touchscreen for control with 12v power outlet
- US or UK face plate options
FEATURES TURNED UP TO 11
However it’s not all about the A/V when it comes to HDBaseT; with increased functionality on all fronts, the SW-130-TX can be used to send power triggers to a compatible connected screen, allowing centralized control and is PoH compatible meaning it can be passively powered over HDBaseT from a compatible receiver. The SW-130-TX can even power & charge a phone or tablet connected to the USB-C port so you don’t run out of juice mid-flow (max. 5v 2A)
HDCP 2.2 COMPATIBLE
The industry’s latest encryption standard designed to stop the illegal copying & distribution of 4K UHD content; no longer unique to residential solutions WyreStorm presentation switchers are fully compliant with HDCP 2.2, enabling you to de-centralize source devices within an installation.
USB 2.0 PASS-THROUGH
With this purpose in mind, HDBaseT2.0 affords the addition of USB 2.0 pass-through, offering not only KVM functionality for extension of a keyboard/mouse or touchscreen but also full data transfer capabilities. The SW-130-TX has a USB host port allowing USB device data to be routed into the selected laptop (via HDMI). Going further, it can send USB device data natively through the USB-C port allowing a single cable to be used for A/V and USB device connectivity.
In the Box
1x SW-130-TX In-wall Transmitter
1x 4‐pin Phoenix Male Connector
1x USB host cable (Type A-B)
1x Decora face plate (SW-130-TX)
4x Retaining screws (SW-130-TX)
1x Quickstart guide
Specifications
TRANSMISSION
Transmission Encoding: HDBaseT Class C | PAM16 Encoding
End to End Latency: 10µs
Max. Transmission Bit Rate: 10.2Gbps
VIDEO
HDMI: (v2.0b) TMDS | 340MHz Maximum
Inputs: 2x HDMI In: 19-pin type A1x USB-C In: USB 3.1c Audio/Video (4.5Gbps)
Outputs: 1x HDBT out: 8-pin RJ45
Max Pixel Clock: HDMI & HDBaseT: 340MHz
Video Resolution (Max): 1920x1080p @60Hz // 2560x1440p @60Hz // 3840x2160p @30Hz 8bit 4:4:4 // 3840x2160p @30Hz 10bit 4:2:0 HDR // 3840x2160p @30Hz 12bit 4:2:2 HDR
Note: WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
Supported Standards: DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
AUDIO
Inputs: 1x Audio In: 3.5mm (1/8in) TRS Stereo // 2ch audio over HDBaseT | 1-way to RX
Audio Formats: 2ch PCM | Multichannel up to DTS-X and Dolby Atmos
Maximum Sampling Rate: 192KHz
Maximum Audio Channels: 32
Audio Return Channel (ARC): Not Supported
COMMUNICATION & CONTROL
USB Host (HDMI Inputs): 1x Type B host | Maximum data throughput: 190Mbps
HDMI: Alt-mode Supported | A/V and USB data from RX
USB 3.1c: HDMI | HDCP 2.2 | EDID | CEC | 2ch audio | USB
RS-232: 1x RS-232: 4-pin Phoenix | Shared with 12v DC input // Compatible with WyreStorm TS-280 touchscreen via 4-pin phoenix port (only when using PoH)
HDCP: Pass-Through, 2.3 Supported
EDID: Pass-Through, from RX
Consumer Electronics Control (CEC): One-way display trigger to RX
Auto Low Latency Mode (ALLM): Supported
Variable Refresh Rate (VRR): Supported
POWER
Power Supply: 12V DC 1A (not included)
Max Power Consumption: 7.8W
Power-over-HDBaseT (PoH): Supported, 1-way from RX
Local Power Supply Input: 4-pin Phoenix
